Ohio Game Fishing



Go Back  Ohio Game Fishing Community > General Discussions > The Lounge >

Need EZ Steer Part

Reply
 
Thread Tools Display Modes
Old 03-26-2012, 11:58 AM   #1
nooffseason
On the water
 

Join Date: Nov 2008
Posts: 651
iTrader: 0 / 0%
Default Need EZ Steer Part

Hey guys, I need a part and trying to find the most cost-effective way of ordering it. The final trip last season the straps busted on my EZ Steer assembly connecting to the kicker. As I was fooling around looking at it, I took the connector piece off and just dropped it right in the lake. I believe here is the part number I'm in need of.

Part# 50010

It's the piece that connects to the lower unit of the kicker motor and steers it. Anyone have any suggestions for getting just this piece? I have everything else. Thank you
nooffseason is offline   Reply With Quote

Register today to remove this advertisement IT'S FREE



Old 03-26-2012, 12:07 PM   #2
nicklesman
Dough Boy
 
nicklesman's Avatar
 

Join Date: Jun 2006
Location: Ravenna
Posts: 1,495
iTrader: 9 / 100%
Default

Is this the clamp on type if so I have one located in Ravenna.

Outdoor Hub mobile, the outdoor information engine
__________________
"Fishing is not a sport it is a way of life"
nicklesman is online now   Reply With Quote
Old 03-26-2012, 01:38 PM   #3
Rednek
"The Widow's Son"
 
Rednek's Avatar
 

Join Date: Nov 2006
Location: Perrysville
Posts: 397
iTrader: 2 / 100%
Default

http://www.marinetechproducts.com/pages/EZSteerHome
__________________
Rednek

www.rednekoutfitters.com
Rednek is offline   Reply With Quote
Old 03-26-2012, 05:11 PM   #4
nooffseason
On the water
 

Join Date: Nov 2008
Posts: 651
iTrader: 0 / 0%
Default

Thanks guys, I appreciate the replies. Ended up getting through to them on the phone. Gonna cost me about $50 bucks after shipping. Thanks for the offer, nickles. If I was a little closer, I may have tried to arrange to meet up and offer you a few bucks.
nooffseason is offline   Reply With Quote
Old 03-26-2012, 05:13 PM   #5
eriewalleye
Senior Member
 

Join Date: Feb 2008
Location: Linesville, PA
Posts: 245
iTrader: 3 / 100%
Default

Check Amazon.com
eriewalleye is offline   Reply With Quote
Old 03-30-2012, 02:40 PM   #6
c. j. stone
Senior Member
 

Join Date: Sep 2006
Location: Near Hartville
Posts: 5,184
iTrader: 9 / 100%
Default

If the "lost" part is the brass female receiver part, you could make one with a thin piece of steel plate say 2"X4", two close(think it's a quarter inch?) pipe nipples, one elbow, and the female quick connect fitting for an air hose! You would have to(or have a friend) weld one nipple to the plate. [The quick connect air line fitting is the exact same one they use to make the kit.]
c. j. stone is offline   Reply With Quote
Reply

« bats | Piers »
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:05 PM.












Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2014, Game Fishing LLC